Report inadequate content

4/03/2014

with OM2 Duplex 1Gbit/s systems.Suitable for simple

OM2 patch cords are terminated with standard connectors giving optimum optical performance.FiberFab Multimode Patch Cords are used to connect high speed and legacy networks like Gigabit Ethernet, Fast Ethernet and Ethernet. Multimode patch cords conform to IEC, EIA TIA and Telcordia standards. OM2 patch cords are terminated with standard FiberFab connectors giving optimum...

{
}

3/03/2014

SFP+ Transceivers with challenging thermal environments

Myricom has qualified the transceivers from each source for performance and reliability. Some of the  SFP+ Transceivers sfpcables.com supplied by Myricom have Myricom labeling, as shown, and some have the manufacturers standard labeling.The 10GBase-SR transceivers operate at an 850nm optical wavelength, and are designed for 50?m (50/125) multimode fiber at distances of 26-82m...

28/02/2014

OM1 Duplex snug fit with incredibly low db loss

Each cable has strain relief boots to prolong and maintain performance levels of the assembly, transmit and receive 'legs' of each OM1 Duplex cable are identified by means of ring type cable marker fixed to each end the assembly. A short distance from these identification rings heat shrink is applied to maintain an easy to manage bonded two fibre cable, finally a label...

26/02/2014

SFF 8088 Cable 6Gb/s AWG30 per second

I've seen user reports on the web that say this combo works amazingly well.The SFF-8088 connector is a very widely used connector type that is commonly used today on SAS cards. It carries the equivalent of four SATA/ SAS 7-pin connections through a SFF-8087 to SFF-8088 cable providing 12gbps of throughput using SAS or SATA II 3.0gbps devices. In fact, many makes of SFF-8088...

{
}

25/02/2014

MiniSAS Cables well as an active cable detection

Constructed of high quality materials this 2-meter SAS cable is backed by StarTech.com's Lifetime Warranty.MiniSAS Cables product is the next generation SAS storage interface, addressing channel bandwidth requirements of 6 Gb/s to 12 Gb/s, meeting or exceeding the respective SAS 2.1 and proposed SAS 3.0 specifications. The Mini-SAS HD product provides greater port density (11 mm ...

21/02/2014

SFP+ Passive DAC solutions and up to 7m

While data center administrators have a number of 10GE interfaces to choose from, including 10GBASE-CX4, SFP+ Fiber, SFP+ Passive DAC, and 10GBASE-T, it is the current generation of 10GBASE-T technology that is driving mass adoption of 10GE. This multi-part article analyzes the key differences between 10GBASE-T and other 10GE physical layer technologies, and the impact of...

20/02/2014

SFP+ Cables radius requirements of cable close to the connector

The SFP+ product family includes cable assemblies, cages and connectors.Our SFP+ direct attach copper cable assemblies provide a cost-effective solution over fiber optics in short reach applications. The design allows for serial data transmission up to 10Gbps in each direction. The mechanical design of the cable braid crimp and EMI skirt suppress EMI radiation. Low power ...

19/02/2014

QSFP+ cages are part of the end-to-end solution that Mellanox

Siemon Interconnect Solutions QSFP+ (Quad Small Form-factor Pluggable Plus) Copper Cable assemblies were developed for high-density applications, offering a cost-effective, low-power option for high-speed data center interconnects up to 10 meters. The QSFP+ form factor (Quad SFP+) can replace up to four standard SFP+ connections, providing greater density and reduced system ...

18/02/2014

(SFP) transceivers operate at SFP 1.25Gb/s and are compatible

In 1000BASE-T and 100BASE-TX modes, the transmit data stream is scrambled to reduce radiated emissions and to ensure that there is no correlation between symbols in the data stream.Supporting 10/100/1000 Mbps data-rate in excess of 100 meters (325 feet) reach over UTP Category 5/5e cables, the robust SFP-1GBT-05 transceiver module is ideally suited for implementing small ...